- API
An all MMIC Replacement for Gunn Diode Oscillators Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:36:37.000ZWe propose to replace the Gunn Diode Oscillators (GDOs) in NASA?s millimeter- and submillimeter-wave sensing instruments. Our new solution will rely on modern and reliable microwave integrated circuit technology. Specifically our systems will use highly developed microwave oscillators to achieve a low noise and highly stable reference signal in the 10 ? 30 GHz band. Compact amplifiers based on commercial MMIC chips will then increase the signal strength. Finally, our innovative integrated varactor multiplier circuits will be used to increase the frequency to the 60 ? 150 GHz frequency band with high efficiency and minimal added phase noise. With this technology we expect to achieve phase noise and stability comparable to the best Gunn diode oscillators and fundamentally improved output power and frequency agility. The millimeter-wave integrated circuit process and diode technologies are the critical innovative technologies that are required for this research. Through this SBIR project these innovative technologies will be extended to achieve highly compact multipliers for the 60 ? 150 GHz band. These new multipliers will be integrated with highly developed microwave components to achieve a robust and cost efficient replacement for the GDOs presently used in NASA?s Earth Science program.
- API
AtOrAboveProficient
datahub.smcgov.org | Last Updated 2016-08-30T23:34:30.000ZSTAR Third Grade Reading Scores as a Percentage of Economically Disadvantaged Students classified by the State of California Department of Education as being "At or Above Proficient" reading level for 2013 school year. Hillsborough Unified School District reported a third grade enrollment of 183 students, with 1 student tested. Test results cannot be reported due to identity protection requirements. Las Lomitas Elementary School District reported a third grade enrollment of 170 with 3 students tested. Test results cannot be reported due to identity protection requirements. Menlo Park City Elementary District reported a third grade enrollment of 352 with 6 students tested. Test results cannot be reported due to identity protection requirements. Portola Valley Elementary School District reported a third grade enrollment of 80 with 3 students tested. Test results cannot be reported due to identity protection requirements. Woodside School District reported a third grade enrollment of 51 with 2 students tested. Test results cannot be reported due to identity protection requirements.
- API
Additive Manufacturing Technology Development Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:39:10.000Z<p>The 3D Printing In Zero-G (3D Print) technology demonstration project is a proof-of-concept test designed to assess the properties of melt deposition modeling additive manufacturing in the microgravity environment experienced on the International Space Station (ISS). The lessons learned from this technology demonstration will be used for the next generation of melt deposition modeling in the permanent NanoRacks Additive Manufacturing Facility (AMF) as well as for any future additive manufacturing technology NASA plans to use, such as metals or electronics in-space manufacturing, on both the ISS and Deep Space Missions. This demonstration is the first step towards realizing a &ldquo;machine shop&rdquo; in space, a critical enabling component of any Deep Space Mission.</p><p>The 3D Print payload consists of a 3D printer (a two-axis extruder mobility system, a single-axis print tray mobility system, the extruder and accompanying feedstock cartridge, the print tray, Environmental Control Unit (ECU, a prototype for the permanent AMF), an electronics box, and all of the necessary cables and bolts to attach the device to the ISS Microgravity Science Glovebox&nbsp;(MSG) cold plate, MSG laptop computer, and MSG power supply) and all identified spare parts. The 3D Print payload will operate within the MSG. The payload uses extrusion-based additive manufacturing technology to fabricate objects. Additive manufacturing is the process of creating three dimensional objects from a Computer Aided Design (CAD) model where material is deposited layer by layer. The 3D Print payload will extrude a bead of thermo-polymer material from a larger diameter feedstock material. When one layer is complete, the next layer is printed on top and bonded to the lower layer while still molten. This creates an adhesive bond as opposed to a solid material extrusion.</p><p>Performance goals were defined realizing the 3D Print is a technology demonstration. The following is a list of minimum success criteria:<br />1. Successful integration and safe operation in the MSG on the ISS<br />2. Demonstration of extrusion based additive manufacturing using polymeric material<br />3. Successful extrusion and traversing<br />4. Printing of one part while in ISS microgravity<br />5. Mitigation of functional risks for future facilities<br />6. Comparison of ISS printed parts with those printed on Earth (dimensional and strength testing).</p>
- API
Vibration-Free Cooling Cycle Pump for Space Vehicles and Habitats Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:26:51.000ZMainstream Engineering Corporation completed the design of a high-speed pump for International Space Station (ISS) Environmental Control and Life Support Systems and future spacecraft and extraterrestrial outpost applications. Specifications for this pump were derived from an existing pump currently operating as part of the thermal control loop on the ISS. The design includes magnetic bearings so that a vibration-reducing control algorithm can be implemented. A digital controller was designed, which measured and reduced vibration-causing fluctuations in shaft displacement due to rotor unbalance in multiple axes. The controller was tested over an operating speed range of 600 to 7200 rpm with excellent results. The controller reduced mean shaft displacement by 71% over the entire operating range, and reduced it by more than 80% at higher operating speeds where synchronous vibration was dominant. In Phase II the magnetic bearing equipped cooling loop pump designed in Phase I will be fabricated and tested. Mainstream will demonstrate the added efficiency, reliability, and low vibration of the system as compared with the existing pump. The pump assembly will undergo vibration characterization testing with support from Marshall Space Flight Center.
- API
Stable, Extreme Temperature, High Radiation, Compact. Low Power Clock Oscillator for Space, Geothermal, Down-Hole & other High Reliability Applications Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:30:08.000ZEfficient and stable clock signal generation requirements at extreme temperatures (-180C to +450C)and radiation (&gt;250 Krad TID) are not met with the current solutions.Chronos technology proposes to design and fabricate RTXO as a new, comprehensive and scalable solution that simultaneously addresses the attributes of a reliable clock source in extreme environments. RTXO offers very small form-factor 5X7mm surface mount device utilizing high-Q Quartz material and CMOS/SOI for the extreme cold temperatures of Mars surface up to +110C. For extreme high temperature (to +450C) it uses Silicon Carbide (SiC-4H) semiconductor technology, high quality Gallium Orthophisphate (GaPO4) piezo-electric resonator material in a non-adhesive configured innovative assembly. All the different elements and processes used in the RTXO technology have been investigated in phase I to comply with the intended performance. This includes the individual elements, packaging, interconnecting method and manufacturing processes. RTXO offers standard signal interface, wide operating voltage range, conventional microelectronic packaging, and industry standard and reliable metal to metal as well as glass to metal sealing processes. RTXO delivers its exceptional performance over a wide (application specific) frequency range to 100 MHz from a single supply voltage and requires very low power.
- API
Approximate Cartesian Control for Robotic Tool Usage with Graceful Degradation Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:31:39.000ZMany of NASA's exploration scenarios include important roles for autonomous or partially autonomous robots. It is desirable for them to utilize human tools when possible, rather than needing to build custom tools for each robot. Control of robotic manipulators for tool usage generally requires a very precise Cartesian-space trajectory of the tool tip (e.g., moving a marker along the surface of a whiteboard or rotating a screwdriver about an axis). Well-known techniques exist for manipulator control in Cartesian space, most of which necessitate solving a series of Inverse Kinematics (IK) problems. Closed-form IK solvers work well for 7-degree-of-freedom (DOF) arms with rigid tool attachments, but cannot handle non-rigid tools that slip in the robot's hands. Numerical IK approaches are more generic and can handle non-rigid links to tools, but can be slow to converge. More importantly, if any joints fail or become limited in their range of motion, the robot arm essentially becomes 6-DOF or lower. IK solvers often fail in these lower DOF spaces because the configuration space becomes non-continuous and full of "holes". As a result, a 7-DOF robotic arm in space might be rendered largely useless if a single joint fails or even loses mobility until it can be serviced. TRACLabs proposes to investigate an alternative approach to traditional Cartesian control approaches, which rely on complex IK solvers that go from Cartesian space backwards to joint space. We propose to leverage cheap memory and modern processing speeds to instead perform simple computations that go from joint space forwards to Cartesian space. Such techniques should overcome common changes to a manipulation chain caused by tool slippage or the grasping of a new tool and to overcome uncommon changes to a chain caused by joint failures, reduced joint mobility, changes in joint geometry or range of motion, or added joints.
- API
Bronx School Survey - 2011
bronx.lehman.cuny.edu | Last Updated 2012-09-27T18:59:36.000ZEvery year, all parents, all teachers, and students in grades 6 - 12 take the NYC School Survey. The survey ranks among the largest surveys of any kind ever conducted nationally. Survey results provide insight into a school's learning environment and contribute a measure of diversification that goes beyond test scores on the Progress Report. NYC School Survey results contribute 10% - 15% of a school's Progress Report grade (the exact contribution to the Progress Report is dependant on school type). Survey questions assess the community's opinions on academic expectations, communication, engagement, and safety and respect. School leaders can use survey results to better understand their own school's strengths and target areas for improvement. The NYC School Survey helps school leaders understand what key members of the school community say about the learning environment at each school. The information captured by the survey is designed to support a dialogue among all members of the school community about how to make the school a better place to learn. New York City parents, students, and teachers reached new all-time participation highs on the 2011 School Survey. 960,191 surveys were submitted.
- API
ICI - Accommodation and Food Services Garbage Composition - Proper Disposal Location
data.calgary.ca | Last Updated 2023-02-01T15:39:37.000ZThis chart shows weight per cent composition grouped by proper disposal location. This dataset is for garbage bin waste from the Industrial, Commercial, and Institutional (ICI) sector. The North American Industry Classification System (NAICS) is used to categorize ICI businesses and organizations into sub-sectors for ease of data collection and reporting. The NAICS sub-sectors included in this study are: Accommodation and Food Services (NAICS code 72), Retail Trade (44-45), Manufacturing (31-33), Health Care and Social Assistance (62), and Public Administration (91). All businesses and organizations included in the study were customers of The City’s Commercial Collections service, except for one privately-serviced customer in the Accommodation and Food Services sub-sector that was added to provide better sector representation. A total of 115 samples are included in the dataset: 30 in Accommodation and Food Services, 35 in Retail Trade, 17 in Manufacturing, 25 in Health Care and Social Assistance, and 8 in Public Administration. The weight per cent for each sub-sector is the pooled average of samples collected in the four seasons of 2019. Waste Composition studies are periodically conducted by Waste and Recycling Services to help assess the performance of diversion and education programs and inform improvements and new program design.
- API
Compact, Lightweight, Efficient Cooling Pump for Space Suit Life Support Systems Project
nasa-test-0.demo.socrata.com | Last Updated 2015-07-20T05:21:32.000ZWith the increasing demands placed on extravehicular activity (EVA) for the International Space Station assembly and maintenance, along with planned lunar and Martian missions, the need for increased human productivity and capability becomes ever more critical. This is most readily achieved by reduction in space suit weight and volume, and increased hardware reliability, durability, and operating lifetime. Considerable progress has been made with each successive generation of space suit design; from the Apollo A7L suit, to the current Shuttle Extravehicular Mobile Unit (EMU) suit, and the developmental I-Suit and Mark III suits. However, one area of space suit design which has continued to lag is the fluid pump used to drive the water cooling loop of the Primary Life Support System (PLSS). Conventional electric motor-driven fluid pumps are heavy, bulky, inefficient, and prone to wear. A new pump type is needed. Lynntech proposes to further reduce the size, weight and power consumption of its long-life, low-power, compact, lightweight, efficient electrochemically-driven pumps, which will allow their use in the next generation space suit.
- API
Global Navigation Satellite System (GNSS) IGS Clock Combination Product from Real-Time AC Submissions from NASA CDDIS
data.nasa.gov | Last Updated 2022-01-17T05:22:33.000ZThis derived product set consists of Global Navigation Satellite System satellite and receiver clock combination product (30-second granularity, daily files, generated daily) from the real-time IGS analysis center submissions available from NASA Crustal Dynamics Data Information System (CDDIS). GNSS provide autonomous geo-spatial positioning with global coverage. GNSS data sets from ground receivers at the CDDIS consist primarily of the data from the U.S. Global Positioning System (GPS) and the Russian GLObal NAvigation Satellite System (GLONASS). Since 2011, the CDDIS GNSS archive includes data from other GNSS (Europe’s Galileo, China’s Beidou, Japan’s Quasi-Zenith Satellite System/QZSS, the Indian Regional Navigation Satellite System/IRNSS, and worldwide Satellite Based Augmentation Systems/SBASs), which are similar to the U.S. GPS in terms of the satellite constellation, orbits, and signal structure. The CDDIS provides access to products generated from real-time data streams in support of the IGS Real-Time Service. The real-time observation data from a global permanent network of ground-based receivers are transmitted from the CDDIS in 1 to multi-second intervals in raw receiver or RTCM (Radio Technical Commission for Maritime Services) format. These real-time data are utilized to generate near real-time product streams. The real-time products consist of GNSS satellite orbit and clock corrections to the broadcast ephemeris. These correction streams are formatted according to the RTCM SSR standard for State Space Representation and are broadcast using the NTRIP protocol. IGS analysis centers (ACs) access GNSS real-time data streams to produce GNSS satellite and ground receiver clock values in real-time. The product streams are combination solutions generated by processing individual real-time solutions from participating IGS Real-time ACs. The IGS Real-Time Analysis Center Coordinator (RTACC) uses these individual AC solutions to generate this real-time IGS combined satellite and receiver clock product. The effect of combining the different AC solutions is a more reliable and stable performance than that of any single AC's product. This clock solution is a batch combination based on daily clock submissions by these IGS real-time analysis centers and have been provided since February 2009, shortly after real-time streams were routinely available through the IGS Real-Time Pilot Project and prior to the availability of real-time product streams. Clock solution files consist of decoded clock results from the real time stream at 30-second intervals. This combination is a daily solution available approximately one to three days after the end of the previous UTC day. All satellite and receiver clock solution files utilize the clock RINEX format and span 24 hours from 00:00 to 23:45 UTC.